|
| FW-1 |
Wind Isotach (MPH) Map of Western United States |
| FW-2 |
Wind Isotach (MPH) Map of Eastern United States |
| FW-3 |
Wind Isotach (MPH) Map of the Gulf States |
| FW-4 |
Wind Isotach (MPH) Map of Florida |
| FW-5 |
Wind Isotach (MPH) Map of North Eastern United States |
| FW-6 |
Wind Isotach (MPH) Map of Alaska |
| |
|
|
| FA-1 |
Fastening Pattern: Screws and Plates |
| FA-2 |
Single-Layer of Fire Sheet |
| FA-3 |
Fully Adhered-Fleece Back Laps |
| FA-4 |
Fastening Pattern for 4x4 Insulation (4,5,6,8) |
| FA-5 |
Fastening Pattern for 4x4 Insulation (9,10,11,12) |
| FA-6 |
Fastening Pattern for 4x4 & 4x8 Insulation (14,16,8) |
| FA-7 |
Fastening Pattern for 4x8 Insulation (10,11) |
| FA-8 |
Fastening Pattern for 4x8 Insulation (12,16) |
| FA-9 |
Fastening Pattern for 4x8 Insulation (20,21) |
| FA-10 |
Determine Whether You Have a Corner Zone |
| FA-11 |
Typical Insulation Layout |
| FA-12 |
4' Cover-Board Zone Layout |
| FA-13 |
8' Cover-Board Zone Layout |
| FA-14 |
12' Cover-Board Zone Layout |
| FA-15 |
4' Insulation Zone Layout |
| FA-16 |
8' Insulation Zone Layout |
| FA-17 |
12' Insulation Zone Layout |
| FA-18 |
Cricket Layout |
| |
|
|
| FE-1 |
Edge Termination |
| FE-2 |
Butt-Joint Details |
| FE-3 |
Clad Edge Metal |
| FE-4 |
Peel-Stop Detail |
| FE-5 |
Terma-Edge Detail |
| FE-6 |
Econo-Snap Edge Detail |
| FE-7 |
Back-Wrapped Edge |
| FE-8 |
Aluminum Termination Bar Edge |
| FE-9 |
Raised Rake Edge |
| FE-10 |
Raised Fascia Edge |
| |
|
|
| FB-1 |
Stucco Tie-In |
| FB-2 |
Siding Tie-In |
| FB-3 |
Steep Slope Tie-In |
| FB-4 |
Reglet Metal Flashing |
| FB-5 |
Termination Bar Detail |
| FB-6 |
IB Clad Termination Bar |
| FB-7 |
Back-Wrapped Termination Bar |
| FB-8 |
Rough Maced Wall Base Flashing |
| FB-9 |
Elevation Change Tie-In |
| FB-10 |
IB Clad Metal Elevation Change Tie-In |
| FB-11 |
Adhered Parapet Wall with Metal Coping |
| FB-12 |
Loose Laid High Wall Termination Bar Attachment |
| FB-13 |
Loose Laid High Wall Screws & Plates Attachment |
| FB-14 |
Backer Strip Attachment |
| FB-15 |
Cricket Wall |
| FB-16 |
Inside / Outside Corners |
| FB-17 |
Roof Curb / Hatch Detail (Canted) |
| FB-18 |
Roof Curb / Hatch Detail |
| FB-19 |
Encapsulated Support Details |
| FB-20 |
WP Hickman Counter Flashings |
| FB-21 |
WP Hickman Coping Cap |
| |
|
|
| FX-1 |
Canted Curb Expansion / Area Divider Detail |
| FX-2 |
Curb to Curb Expansion / Area Divider Detail |
| FX-3 |
Roof to Wall Expansion Joint Detail |
| |
|
|
| FT-1 |
Base Flashing Termination Options Detail |
| |
|
|
| FD-1 |
Tapered Sump Clamping Ring Drain |
| FD-2 |
Clamping Ring Drain |
| FD-3 |
Retrofit Drain |
| FD-4 |
Drain-Overflow Sump Layout |
| FD-5 |
PVC Drop Drains |
| FD-6 |
PVC Scupper-Drain |
| FD-7 |
Clad Metal Wall Scupper |
| |
|
|
| FP-1 |
Heater Stack Detail |
| FP-2 |
Cone Flashing |
| FP-3 |
Stantion Support |
| FP-4 |
Roof and Membrane Vents |
| FP-5 |
Membrane Vent Over Existing Roof |
| FP-6 |
Isolation Pads |
| FP-7 |
Chemical Pitch-Pan Detail |
| FP-8 |
Pitch-Pan Detail |
| |
|
|
| FM-1 |
T-Joint Patches |
